Error (10500): VHDL syntax error at text.vhd(6) near text "FORT"; expecting "is"
Error (10500): VHDL syntax error at text.vhd(6) near text ?
Error (10500): VHDL syntax error at text.vhd(6) near text ?
Error (10500): VHDL syntax error at text.vhd(7) near text ?
Error (10500): VHDL syntax error at text.vhd(7) near text ?
Error (10500): VHDL syntax error at text.vhd(8) near text ?
Error (10500): VHDL syntax error at text.vhd(8) near text ?
Error (10500): VHDL syntax error at text.vhd(9) near text ?
Error (10500): VHDL syntax error at text.vhd(9) near text ?
Error (10500): VHDL syntax error at text.vhd(10) near text ?
Error (10500): VHDL syntax error at text.vhd(10) near text ?
Error (10500): VHDL syntax error at text.vhd(11) near text ?
Error (10500): VHDL syntax error at text.vhd(11) near text ?
Error (10500): VHDL syntax error at text.vhd(12) near text ?
Error (10500): VHDL syntax error at text.vhd(12) near text ?
Error (10500): VHDL syntax error at text.vhd(15) near text ?
Error (10500): VHDL syntax error at text.vhd(15) near text "?; expecting ":", or ","
Error (10500): VHDL syntax error at text.vhd(15) near text ?
Error (10500): VHDL syntax error at text.vhd(16) near text ?
Info: Found 0 design units, including 0 entities, in source file text.vhd
Error: Quartus II 64-Bit Analysis & Synthesis was unsuccessful. 19 errors, 8 warnings
Error: Peak virtual memory: 4446 megabytes
Error: Processing ended: Fri Dec 11 15:40:37 2020
Error: Elapsed time: 00:00:00
Error: Total CPU time (on all processors): 00:00:01
這錯誤讓我眼花啊，大佬幫幫忙唄
這是程式
LIBRARY IEEE;
USE IEEE.STD_LOGIC_1164.ALL;
USE IEEE.STD_LOGIC_ARITH.ALL;
USE IEEE.STD_LOGIC_UNSIGNED.ALL;
ENTITY KONGZHI3NIS
FORT(RESET：IN STD_LOGIC;
SYSSTART：IN STD_LOGIC;
FLAG：IN STDLOGIC;
BASECLK：IN STD_LOGIC;
STOP：IN STD_LOGIC;
RESETOUT：OUT STD_LOGIC;
STARTCUNCHU：OUT STD_LOGIC);
END KONGZHI3;
ARCHITECTURE BEHAV OF KONGZHI3 IS
SIGNAL KRESETOUT：STD_LOGIC;
SIGNAL KSTARTOUT：STD_LOGIC;
BEGIN
P1：PROCESS(RESET,SYSSTART,FLAG,BASECLK)
BEGIN
IF(FLAG=‘1’)THEN
IF(SYSSART=‘1’)THEN
IF(RESET=‘1’)THEN
IF(BASECLK’EVENT AND BASECLK=‘1’)
KSTARTOUT<=SYSSTART;
STOP<=‘1’;
SLSIF RESET='0' THEN KRESETOUT<=‘1’;
END IF;
END IF;
END IF;
END IF;
END PROCESS;
RESETOUT<=KRESETOUT;
STARTCUNCHU<=KSTARTOUT;
END BEHAV;
uj5u.com熱心網友回復：
KONGZHI3N 中間是否少了空格？ IS轉載請註明出處，本文鏈接：https://www.uj5u.com/qita/233256.html
標籤：硬件設計
上一篇：充電問題
下一篇：vmware備份重刪