我用XC7Z010iclg400，外掛sp的512M QSPI FLASH，通過JTAG加載BOOT.bin，一直提示FLASH初始化不過，哪位高手指點一二，感激不盡！！
cmd /C program_flash -f E:\ZYNQ_PRJ\Z7_TEST0\UART_x8\FSBL\BOOT3.bin -offset 0 -flash_type \
qspi_single -fsbl E:\ZYNQ_PRJ\Z7_TEST0\UART_x8\UART_x8.sdk\FSBL\Debug\FSBL.elf -cable type \
xilinx_tcf url TCP:127.0.0.1:3121
****** Xilinx Program Flash
****** Program Flash v2018.1 (64-bit)
**** SW Build 2188600 on Wed Apr 4 18:40:38 MDT 2018
** Copyright 1986-2018 Xilinx, Inc. All Rights Reserved.
Connected to hw_server @ TCP:127.0.0.1:3121
Available targets and devices:
Target 0 : jsn-DLC9LP-00000000000000
Device 0: jsn-DLC9LP-00000000000000-4ba00477-0
Retrieving Flash info...
Initialization done, programming the memory
===== mrd->addr=0xF800025C, data=https://bbs.csdn.net/topics/0x00000001 =====
BOOT_MODE REG = 0x00000001
WARNING: [Xicom 50-100] The current boot mode is QSPI.
If flash programming fails, configure device for JTAG boot mode and try again.
===== mrd->addr=0xF8007080, data=https://bbs.csdn.net/topics/0x30800100 =====
===== mrd->addr=0xF8000B18, data=https://bbs.csdn.net/topics/0x00000000 =====
Downloading FSBL...
Running FSBL...
Finished running FSBL.
===== mrd->addr=0xF8000110, data=https://bbs.csdn.net/topics/0x000FA220 =====
READ: ARM_PLL_CFG (0xF8000110) = 0x000FA220
===== mrd->addr=0xF8000100, data=https://bbs.csdn.net/topics/0x00028008 =====
READ: ARM_PLL_CTRL (0xF8000100) = 0x00028008
===== mrd->addr=0xF8000120, data=https://bbs.csdn.net/topics/0x1F000200 =====
READ: ARM_CLK_CTRL (0xF8000120) = 0x1F000200
===== mrd->addr=0xF8000118, data=https://bbs.csdn.net/topics/0x000FA240 =====
READ: IO_PLL_CFG (0xF8000118) = 0x000FA240
===== mrd->addr=0xF8000108, data=https://bbs.csdn.net/topics/0x00030008 =====
READ: IO_PLL_CTRL (0xF8000108) = 0x00030008
Info: Remapping 256KB of on-chip-memory RAM memory to 0xFFFC0000.
===== mrd->addr=0xF8000008, data=https://bbs.csdn.net/topics/0x00000000 =====
===== mwr->addr=0xF8000008, data=https://bbs.csdn.net/topics/0x0000DF0D =====
MASKWRITE: addr=0xF8000008, mask=0x0000FFFF, newData=https://bbs.csdn.net/topics/0x0000DF0D
===== mwr->addr=0xF8000910, data=https://bbs.csdn.net/topics/0x000001FF =====
===== mrd->addr=0xF8000004, data=https://bbs.csdn.net/topics/0x00000000 =====
===== mwr->addr=0xF8000004, data=https://bbs.csdn.net/topics/0x0000767B =====
MASKWRITE: addr=0xF8000004, mask=0x0000FFFF, newData=https://bbs.csdn.net/topics/0x0000767B
Problem in running uboot
Flash programming initialization failed.
ERROR: Flash Operation Failed
uj5u.com熱心網友回復：
找到解決方法了嗎？uj5u.com熱心網友回復：
空的FLASH，首次需要先用mio管腳配置為JTAG模式燒錄程式，燒錄成功后,MIO改為QSPI模式啟動即可轉載請註明出處，本文鏈接：https://www.uj5u.com/qita/30577.html
標籤：嵌入開發(WinCE)
上一篇：wincc編譯沒有畫面