這里老是出現錯誤uj5u.com熱心網友回復：
改成file.Open(_T("ts.txt"),uj5u.com熱心網友回復：
錯誤是沒有了不過除錯的時候出現這個
uj5u.com熱心網友回復：
跟蹤除錯，看出錯在哪里uj5u.com熱心網友回復：
需要判斷檔案是否打開成功， try catch 捕捉 CFileExceptionuj5u.com熱心網友回復：
你的檔案路徑錯了啊。'\'都換成'\\'uj5u.com熱心網友回復：
CString strPath = _T("");CFileDialog Open(TRUE, _T("*.txt"), NULL, OFN_HIDEREADONLY | OFN_OVERWRITEPROMPT, _T("帳號檔案 (*.txt)|*.txt|All Files (*.*)|*.*||"), NULL);
if (Open.DoModal() == IDOK)
{
strPath = Open.GetPathName();//這就是你要的路徑了。
}
CStdioFile file;
if (!file.Open(strPath, CFile::modeReadWrite))
{
//找開檔案失敗
AfxMessageBox("帳號檔案錯誤");
return;
}
uj5u.com熱心網友回復：
#5 說的對，你那個 \Administrator 這里就有問題，應該是 \\。后面估計還有路徑錯誤，只是擋住了看不見。uj5u.com熱心網友回復：
C++ Character ConstantsCharacter constants are one or more members of the “source character set,” the character set in which a program is written, surrounded by single quotation marks ('). They are used to represent characters in the “execution character set,” the character set on the machine where the program executes.
Microsoft Specific
For Microsoft C++, the source and execution character sets are both ASCII.
END Microsoft Specific
There are three kinds of character constants:
Normal character constants
Multicharacter constants
Wide-character constants
Note Use wide-character constants in place of multicharacter constants to ensure portability.
Character constants are specified as one or more characters enclosed in single quotation marks. For example:
char ch = 'x'; // Specify normal character constant.
int mbch = 'ab'; // Specify system-dependent
// multicharacter constant.
wchar_t wcch = L'ab'; // Specify wide-character constant.
Note that mbch is of type int. If it were declared as type char, the second byte would not be retained. A multicharacter constant has four meaningful characters; specifying more than four generates an error message.
Syntax
character-constant :
'c-char-sequence'
L'c-char-sequence'
c-char-sequence :
c-char
c-char-sequence c-char
c-char :
any member of the source character set except the single quotation mark ('), backslash (\), or newline character
escape-sequence
escape-sequence :
simple-escape-sequence
octal-escape-sequence
hexadecimal-escape-sequence
simple-escape-sequence : one of
\' \" \? \\
\a \b \f \n \r \t \v
octal-escape-sequence :
\octal-digit
\octal-digit octal-digit
\octal-digit octal-digit octal-digit
hexadecimal-escape-sequence :
\xhexadecimal-digit
hexadecimal-escape-sequence hexadecimal-digit
Microsoft C++ supports normal, multicharacter, and wide-character constants. Use wide-character constants to specify members of the extended execution character set (for example, to support an international application). Normal character constants have type char, multicharacter constants have type int, and wide-character constants have type wchar_t. (The type wchar_t is defined in the standard include files STDDEF.H, STDLIB.H, and STRING.H. The wide-character functions, however, are prototyped only in STDLIB.H.)
The only difference in specification between normal and wide-character constants is that wide-character constants are preceded by the letter L. For example:
char schar = 'x'; // Normal character constant
wchar_t wchar = L'\x81\x19'; // Wide-character constant
Table 1.2 shows reserved or nongraphic characters that are system dependent or not allowed within character constants. These characters should be represented with escape sequences.
Table 1.2 C++ Reserved or Nongraphic Characters
Character ASCII
Representation ASCII
Value Escape Sequence
Newline NL (LF) 10 or 0x0a \n
Horizontal tab HT 9 \t
Vertical tab VT 11 or 0x0b \v
Backspace BS 8 \b
Carriage return CR 13 or 0x0d \r
Formfeed FF 12 or 0x0c \f
Alert BEL 7 \a
Backslash \ 92 or 0x5c \\
Question mark ? 63 or 0x3f \?
Single quotation mark ' 39 or 0x27 \'
Double quotation mark " 34 or 0x22 \"
Octal number ooo — \ooo
Hexadecimal number hhh — \xhhh
Null character NUL 0 \0
If the character following the backslash does not specify a legal escape sequence, the result is implementation defined. In Microsoft C++, the character following the backslash is taken literally, as though the escape were not present, and a level 1 warning (“unrecognized character escape sequence”) is issued.
Octal escape sequences, specified in the form \ooo, consist of a backslash and one, two, or three octal characters. Hexadecimal escape sequences, specified in the form \xhhh, consist of the characters \x followed by a sequence of hexadecimal digits. Unlike octal escape constants, there is no limit on the number of hexadecimal digits in an escape sequence.
Octal escape sequences are terminated by the first character that is not an octal digit, or when three characters are seen. For example:
wchar_t och = L'\076a'; // Sequence terminates at a
char ch = '\233'; // Sequence terminates after 3 characters
Similarly, hexadecimal escape sequences terminate at the first character that is not a hexadecimal digit. Because hexadecimal digits include the letters a through f (and A through F), make sure the escape sequence terminates at the intended digit.
Because the single quotation mark (') encloses character constants, use the escape sequence \' to represent enclosed single quotation marks. The double quotation mark (") can be represented without an escape sequence. The backslash character (\) is a line-continuation character when placed at the end of a line. If you want a backslash character to appear within a character constant, you must type two backslashes in a row (\\). (SeePhases of Translation in the Preprocessor Reference for more information about line continuation.)
轉載請註明出處，本文鏈接：https://www.uj5u.com/gongcheng/101201.html
標籤：基礎類