應用：
STM32F407、SPI做從機接收資料、采用DMA接收，預期 接收到512個資料時產生一個DMA中斷，進行資料處理，以下是我的代碼，進不了中斷，不知道為什么？？？求解答：
將中斷改為SPI1_IRQn時可以進中斷，但是資料不對，得到的是一個16位的固定置！
SPI_InitTypeDef SPI_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
DMA_InitTypeDef DMA_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
SPI_Cmd(FPGA_SPI, DISABLE);
SPI_DeInit(FPGA_SPI);
RCC_AHB1PeriphClockCmd (FPGA_SPI_SCK_GPIO_CLK | FPGA_SPI_MISO_GPIO_CLK | FPGA_SPI_MOSI_GPIO_CLK | FPGA_CS_GPIO_CLK, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1, ENABLE);
RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_DMA2, ENABLE);
GPIO_PinAFConfig(FPGA_SPI_SCK_GPIO_PORT,FPGA_SPI_SCK_PINSOURCE,FPGA_SPI_SCK_AF);
GPIO_PinAFConfig(FPGA_SPI_MISO_GPIO_PORT,FPGA_SPI_MISO_PINSOURCE,FPGA_SPI_MISO_AF);
GPIO_PinAFConfig(FPGA_SPI_MOSI_GPIO_PORT,FPGA_SPI_MOSI_PINSOURCE,FPGA_SPI_MOSI_AF);
GPIO_InitStructure.GPIO_Pin = FPGA_SPI_SCK_PIN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(FPGA_SPI_SCK_GPIO_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = FPGA_SPI_MISO_PIN;
GPIO_Init(FPGA_SPI_MISO_GPIO_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = FPGA_SPI_MOSI_PIN;
GPIO_Init(FPGA_SPI_MOSI_GPIO_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = FPGA_CS_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_Init(FPGA_CS_GPIO_PORT, &GPIO_InitStructure);
SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex;
SPI_InitStructure.SPI_Mode = SPI_Mode_Slave;
SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b;
SPI_InitStructure.SPI_CPOL = SPI_CPOL_Low;
SPI_InitStructure.SPI_CPHA = SPI_CPHA_1Edge;
SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;
SPI_InitStructure.SPI_NSS = SPI_NSS_Hard;//SPI_NSS_Soft;
SPI_InitStructure.SPI_CRCPolynomial = 7;
SPI_Init(FPGA_SPI, &SPI_InitStructure);
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
NVIC_InitStructure.NVIC_IRQChannel = DMA2_Stream2_IRQn;//SPI1_IRQn
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
SPI_DMACmd(FPGA_SPI,SPI_DMAReq_Rx,ENABLE);
SPI_Cmd(FPGA_SPI, ENABLE);
while (DMA_GetCmdStatus(SPI_DMA_STREAM) != DISABLE){}
DMA_DeInit(SPI_DMA_STREAM);
DMA_InitStructure.DMA_Channel = SPI_DMA_CHANNEL;
DMA_InitStructure.DMA_PeripheralBaseAddr = (u32)&FPGA_SPI->DR;
DMA_InitStructure.DMA_Memory0BaseAddr = (u32)spi_rv_buf;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralToMemory;
DMA_InitStructure.DMA_BufferSize = SPI_RV_SIZE;
DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;
DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;
DMA_InitStructure.DMA_Mode = DMA_Mode_Normal;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_Init(SPI_DMA_STREAM, &DMA_InitStructure);
DMA_ITConfig(SPI_DMA_STREAM, DMA_IT_TC, ENABLE);
DMA_Cmd(SPI_DMA_STREAM, ENABLE);
uj5u.com熱心網友回復：
void DMA2_Stream2_IRQHandler(void){if(DMA_GetFlagStatus(SPI_DMA_STREAM,DMA_FLAG_TCIF2) == SET)
{
DMA_ClearITPendingBit(SPI_DMA_STREAM,DMA_FLAG_TCIF2);
}
}
轉載請註明出處，本文鏈接：https://www.uj5u.com/qita/212829.html
標籤：單片機/工控